Every cordless power tool works on batteries, whether it is cordless phone or some other cordless tool. It is not always necessary to consider battery voltage while choosing it for your power tool batteries. For the battery tools, it is necessary to look in to the factors such as ampere/hour and battery type. It has been seen that due to battery performance many 14.2 volt tools outperforms 19.4 volt tools.

To rate a cordless tool battery, ampherage hours and voltage are used. You should not be surprised to know that amperage hours are used to determine how long a battery will last and voltage refers to the flow or strength of the electrical current.

It has been proved that higher the voltage in conjunction with higher amp/hr the stronger the battery. You will find that cordless power tool batteries are usually available in 1.4, 2.4 and 3.0 amp/hr. You can find these ratings either at the upper or the lower end of the battery.

When choosing a Cordless Power tool battery, you need also consider the charging time. Many old batteries need to be charged every hour whereas the output of work is too less. And, usually they need to be charged for more than six hours. But, if you have more work to do then it will be total wastage of time. Batteries of good companies such as Makita, Bosch, Hitachi, etc., usually require just 15 to 20 minutes getting recharged.

When purchasing high cost power tool batteries it is also important to follow maintenance instructions given by manufacturers. Batteries need to be serviced regularly for longer life. And, once the battery is worn out it needs to be replaced. But, during replacement it’s economical to change the entire tool kit. This will cost less compare to purchase of new two batteries.

Batteries without power are nothing more than a useless thing. An ideal battery is the one which can sustain power for long and does not stop because of any reason while working. A perfect tool is the necessary thing to get the work done in perfect way without any hindrance and then only the person working with the tool can enjoy its work. Different brands of power tool batteries are available in market like DeWalt, Bosch, Makita, Milwaukee tools, skil etc. They all are known to manufacture batteries with appreciable and different qualities.

There are two main types of power tool batteries corded and cordless batteries. Corded tools are not bounded with time limit; you can work as long as the tool is connected to a power grid or generator. But, there is limitation of length and size of the power cord and standing water on site. You can over come this limitation with the help of a GFCI built into a power cord and by using a thicker wire like 12 gauge wire.

Cordless tools can be used anywhere to provide power until the power charged in the battery lasts. These power tool batteries are as powerful as corded tools and with the help of multiple battery chargers, they can be used at any jobsite. The only drawback with these batteries is that they stop any time holding a charge for various reasons like memory charge buildup, heat sensitivity, and a set number of charging cycles etc.

To give these power tool batteries a long life they should be maintained properly. If you do not use battery regularly then it should be taken out from storage charged or discharged occasionally, otherwise it will fail to function when you need it. While storing your battery make sure that you are storing it in a cool, dry, and clean place away from metal and heat. Battery should never be stored on charger because it overcharges the battery and also diminish its runtime.

Power tool batteries should be clean properly and regularly especially if they are used at rough places like construction sites, landscaping areas, and mechanic shops etc. This should be done to ensure that the dirt do not interfere with the battery connections and cause some functional damage. You can use some alcohol and cotton swabs to clean the battery contacts.

On the job site tools can be a worker’s best friend. On the other side of the fence power tools can become almost a weapon against that same worker – robbing him of his ability to work and ply his or her trade and employment. Power tool safety is the responsibility of every worker and tradesperson.

It is essential that those in the work and labor force be fully trained and have experience in working around power tools. It can be easily and best said that working with electricity and electrical power tools requires planning and extreme care. It might easy to cut corners and do things the “fast way”. Beware this is false economy and can easily lead to mistakes – costly not only in time but in personal injuries and lost wages off the job as well.

Regardless of the perceived skill level and skill sets of those involved on the job, at the job site or on the factory floor safe habits should be practiced always when around or utilizing power tools. Power tools are a double edged sword. Good, powerful, yet when utilized wrongly or without care – a deadly menace. All in a swoop of a second as well.

What basic rules and procedures should be implemented and be in place?

First of al make it a practice to always turn off the power. If at all possible even turn off the power directly at the source – at the main circuit control or circuit power panel itself. You can never be too careful when it comes to electricity and tools powered by electrical power. Next in dealing with electrically powered tools, always used a ground fault circuit interrupter (referred to in the electrical and hydro power trades as GFCI) with every power tool to protect against eclectic shock hazards.

Make it a point never to use power tools near what are “live” electrical wires. Ditto that for natural gas or water pipes – especially if you are when drilling or cutting into walls that may have these pipes or conduits internally where these conduits or pipes could be accidentally broached or penetrated. If so make sure that these pipes, conduits or wires are completely visible at all times.

You may well think that it is nothing, that you have seen it done all the time – yet never ever stand in a puddle or on a damp or somewhat damp floor when working directly with electricity. Along with this rule always make it a sure point to disconnect tools when you are finished with them. In the same manner make it a simple habit to always unplug power tools when bits or blades or switched or changed. Of course along with these simple habits are other instructions such as keep power cords away from sharp edges, never yank on a cord to unplug a tool. Lastly always inspect electrical and power cords for frayed edges. Always use the correct tool for the job, its not always safe to improvise or to use a smaller inadequate tool for the job. Lastly make it a point to always turn power tools off before it is plugged in again.

Play it safe out there on the job site and sites.

William Piker Ace Employment Services Winnipeg Manitoba Canada Post View Wpg Transcona St. Vital Brandon Thompson The Pas Manitoba Canada Jobs Free Manitoba Employment Search

]]> http://www.tooldeal.com/power-tools/trades-tradesmen-power-tool-safety-on-the-job-site/feed 0 http://www.tooldeal.com/power-tools/robt-bosch-tool-corp-accy-hc2071-bosch-sds-plus-s4-rotary-hammer-drill-bits http://www.tooldeal.com/power-tools/robt-bosch-tool-corp-accy-hc2071-bosch-sds-plus-s4-rotary-hammer-drill-bits#comments Thu, 11 Mar 2010 09:54:28 +0000 admin http://www.tooldeal.com/power-tools/robt-bosch-tool-corp-accy-hc2071-bosch-sds-plus-s4-rotary-hammer-drill-bits

• Spiral flute all the way up to the drilling head for rapid dust removal
• Centric tip for optimal hole geometry
• Less drill bit wander due to improved tip shape

Product Description
Carbide tipped drill bit head is harder and more resistant to extreme loads. 4 flute design for fast dust removal. For use in drills requiring SDS plus shanks. No. HC2001: 5 32″ x 4″ x 6″ No. HC2011: 3 16″ x 4″ x 6″ No. HC2041: 1 4″ x 4″ x 6″ No. HC2042:… More >>

Robt Bosch Tool Corp Accy HC2071 Bosch SDS-plus S4 Rotary Hammer Drill Bits

]]> http://www.tooldeal.com/power-tools/robt-bosch-tool-corp-accy-hc2071-bosch-sds-plus-s4-rotary-hammer-drill-bits/feed 0 http://www.tooldeal.com/power-tools/makita-power-tools http://www.tooldeal.com/power-tools/makita-power-tools#comments Thu, 11 Mar 2010 09:11:54 +0000 admin http://www.tooldeal.com/power-tools/makita-power-tools

Makita began building its reputation for quality over 85 years ago, when the company started manufacturing electric motors. Since the first electric power tool was produced by Makita in 1958, users have come to rely on the craftsmanship of these tools as well as the brand’s excellent customer service. Makita owes its reputation for building outstanding quality power.

Today Makita is one of the world’s largest power tool manufacturers with seven manufacturing facilities globally and a selection of over 350 superior, innovative tools. The tools are still engineered to Makita’s exacting standards, in Makita’s own factories.

Makita tools come only in a distinctive teal color, making them easily recognized although this is easily imitated by manufactures who wish to benefit from their reputation as a manufacturer of quality tools.

With tools such as the MXT Cordless Drill, you get an all-metal transmission, one-touch drill-to-driver mode, and precision balance in a lightweight yet heavy-duty body. MXT is the next generation in drilling power and control; high speeds of up to 1,700rpm can be achieved within seconds. In addition to their popular drills, they manufacture a host of power tools that can all be run by the same rechargeable battery.

Makita power tools have the longest lasting and most efficient motors of any power tool on the market. With their dual ball bearings, Makita power tools create less friction, which reduces wear on the motor. Makita tools also contain a high-performance fan, which reduces the working temperature of the tool, increasing its life span. All Makita tools represent good honest value-for-money especially when you consider the amount of Equipment you get that comes as standard (often it’s as good as a free angle grinder or impact driver) with most tools at no extra charge.

All Makita tools are built to the highest standards of quality and innovation, but when that tool breaks down everything is not lost. Being able to change your Makita brushes, you can keep the motor operating at optimum efficiency.

Makita’s top end heavy duty cordless series are mostly based around the new Li-ion type of batteries. Lithium-Ion Battery technology brings power to cordless machines like never seen before. Lithium-ion cordless tools provide more power with less weight.

Whether you need a circular saw or an impact driver, a wrench or a flashlight, Makita offers a full line of cordless products.

Johan Nickson an expert on Makita Power Tools at powertool direct.

]]> http://www.tooldeal.com/power-tools/makita-power-tools/feed 0